mxpic.components.primitives.active.rings#

Route#

class mxpic.components.primitives.active.rings.Route(radius=None, width=None, angle=90, xs=None, layer=None, adapt_width=False, adapt_xs=False, instantiate=False, pinstyle=None, offset=None, varname=None, doc='', PCB=False, modes=None)#

Bases: Interconnect

AED_Ring_PIN#

../../../../_images/AED_Ring_PIN.png
class mxpic.components.primitives.active.rings.AED_Ring_PIN(name=None, ORx=10, ORy=9, IRx=9.35, IRy=8.6, gap=0.2, dual_BUS=False, w_bus=0.45, R_cp=None, A_cp=0, offset_X=0, offset_Y=0, w_wg=0.45, R_att=20, R_att_min=10, A_att=30, Ltp_bus=10, dL_p2p=None, L_tilt=10, xs_ring='strip', sharp_patch=True, Euler_trasition=False, show_pins=False, xs_heater='heater', w_heater=0, xs_metal='metal', w_metal=8, via_h2m=None, isl=None, A_ht=270, ht_notch_dual=True, epin_ht_dX=10, epin_ht_dY=3, via_i2m=None, xs_metal_imp='metal', xs_p='p', xs_n='n', xs_cont_wg=None, w_p=3.0, gap_p_i=1, gap_n_i=1, w_n=3.0, offset_i=0, A_imp_in=180, A_imp_out=180, sp_cont=0.2, w_ovlp=0.1, bus_dopping=True, p_in_n_out=False, cell_xs_transition=None)#

Bases: MRR_AED

AED Ring PIN primitive component.

This component builds the AED Ring PIN layout cell.

Parameters:

  • name (Optional[str], optional) – Unique identifier for the device cell. Default is None.

  • ORx (float, optional) – Value for the ORx parameter. Default is 10.

  • ORy (float, optional) – Value for the ORy parameter. Default is 9.

  • IRx (float, optional) – Value for the IRx parameter. Default is 10 - 0.65.

  • IRy (float, optional) – Value for the IRy parameter. Default is 9 - 0.4.

  • gap (float, optional) – Spacing or gap parameter in microns. Default is 0.2.

  • dual_BUS (bool, optional) – Value for the dual_BUS parameter. Default is False.

  • w_bus (float, optional) – Width parameter in microns. Default is 0.45.

  • R_cp (Any, optional) – Radius parameter in microns. Default is None.

  • A_cp (int, optional) – Angle parameter in degrees. Default is 0.

  • offset_X (float, optional) – Value for the offset_X parameter. Default is 0.

  • offset_Y (float, optional) – Value for the offset_Y parameter. Default is 0.

  • w_wg (float, optional) – Width parameter in microns. Default is 0.45.

  • R_att (float, optional) – Radius parameter in microns. Default is 20.

  • R_att_min (float, optional) – Radius parameter in microns. Default is 10.

  • A_att (float, optional) – Angle parameter in degrees. Default is 30.

  • Ltp_bus (int, optional) – Length parameter in microns. Default is 10.

  • dL_p2p (Optional[float], optional) – Value for the dL_p2p parameter. Default is None.

  • L_tilt (int, optional) – Length parameter in microns. Default is 10.

  • xs_ring (str, optional) – Layer or cross-section name used by the device. Default is ‘strip’.

  • sharp_patch (bool, optional) – Whether to add geometry patches for sharp corners or cladding continuity. Default is True.

  • Euler_trasition (bool, optional) – Value for the Euler_trasition parameter. Default is False.

  • show_pins (bool, optional) – Whether to draw pin markers in the generated layout. Default is False.

  • xs_heater (str, optional) – Layer or cross-section name used by the device. Default is ‘heater’.

  • w_heater (float, optional) – Width parameter in microns. Default is 0.

  • xs_metal (str, optional) – Layer or cross-section name used by the device. Default is ‘metal’.

  • w_metal (float, optional) – Width parameter in microns. Default is 8.

  • via_h2m (Any, optional) – Via definition used between heater and metal layers. Default is None.

  • isl (Any, optional) – Isolation-trench definition used by the electrical layout. Default is None.

  • A_ht (float, optional) – Angle parameter in degrees. Default is 270.

  • ht_notch_dual (bool, optional) – Value for the ht_notch_dual parameter. Default is True.

  • epin_ht_dX (int, optional) – Value for the epin_ht_dX parameter. Default is 10.

  • epin_ht_dY (int, optional) – Value for the epin_ht_dY parameter. Default is 3.

  • via_i2m (Any, optional) – Via definition used between implant and metal layers. Default is None.

  • xs_metal_imp (str, optional) – Layer or cross-section name used by the device. Default is ‘metal’.

  • xs_p (str, optional) – Layer or cross-section name used by the device. Default is ‘p’.

  • xs_n (str, optional) – Layer or cross-section name used by the device. Default is ‘n’.

  • xs_cont_wg (Optional[str], optional) – Layer or cross-section name used by the device. Default is None.

  • w_p (float, optional) – Width parameter in microns. Default is 3.0.

  • gap_p_i (float, optional) – Spacing or gap parameter in microns. Default is 1.

  • gap_n_i (float, optional) – Spacing or gap parameter in microns. Default is 1.

  • w_n (float, optional) – Width parameter in microns. Default is 3.0.

  • offset_i (float, optional) – Value for the offset_i parameter. Default is 0.

  • A_imp_in (int, optional) – Angle parameter in degrees. Default is 180.

  • A_imp_out (int, optional) – Angle parameter in degrees. Default is 180.

  • sp_cont (float, optional) – Spacing or gap parameter in microns. Default is 0.2.

  • w_ovlp (float, optional) – Width parameter in microns. Default is 0.1.

  • bus_dopping (bool, optional) – Value for the bus_dopping parameter. Default is True.

  • p_in_n_out (bool, optional) – Value for the p_in_n_out parameter. Default is False.

  • cell_xs_transition (Any, optional) – Cell or component dependency used by this device. Default is None.

generate_imp_gds()#

STD_Ring_PIN#

../../../../_images/STD_Ring_PIN.png
class mxpic.components.primitives.active.rings.STD_Ring_PIN(name, r_ring=10, w_ring=0.55, gap=0.2, dual_BUS=True, w_bus=0.45, R_cp=None, A_cp=0, offset_X=0, offset_Y=0, w_wg=0.45, R_att=20, R_att_min=10, A_att=30, Ltp_bus=10, dL_p2p=None, L_tilt=10, xs_ring='strip', sharp_patch=True, Euler_trasition=False, show_pins=False, xs_heater='heater', w_heater=0, xs_metal='metal', w_metal=8, via_h2m=None, isl=None, A_ht=270, ht_notch_dual=True, epin_ht_dX=10, epin_ht_dY=3, xs_metal_imp='metal', via_i2m=None, xs_p='p', xs_n='n', xs_cont_wg=None, w_p=3, gap_p_i=1, gap_n_i=1, w_n=3, offset_i=0, A_imp_in=180, A_imp_out=180, xs_pcont='pp', xs_ncont='np', w_pcont=3, w_ncont=3, sp_cont=0.2, w_ovlp=0.2, bus_dopping=True, p_in_n_out=False)#

Bases: AED_Ring_PIN

STD Ring PIN primitive component.

This component builds the STD Ring PIN layout cell.

Parameters:

  • name (str) – Unique identifier for the device cell.

  • r_ring (float, optional) – Radius parameter in microns. Default is 10.

  • w_ring (float, optional) – Width parameter in microns. Default is 0.55.

  • gap (float, optional) – Spacing or gap parameter in microns. Default is 0.2.

  • dual_BUS (bool, optional) – Value for the dual_BUS parameter. Default is True.

  • w_bus (float, optional) – Width parameter in microns. Default is 0.45.

  • R_cp (Any, optional) – Radius parameter in microns. Default is None.

  • A_cp (int, optional) – Angle parameter in degrees. Default is 0.

  • offset_X (float, optional) – Value for the offset_X parameter. Default is 0.

  • offset_Y (float, optional) – Value for the offset_Y parameter. Default is 0.

  • w_wg (float, optional) – Width parameter in microns. Default is 0.45.

  • R_att (float, optional) – Radius parameter in microns. Default is 20.

  • R_att_min (float, optional) – Radius parameter in microns. Default is 10.

  • A_att (float, optional) – Angle parameter in degrees. Default is 30.

  • Ltp_bus (int, optional) – Length parameter in microns. Default is 10.

  • dL_p2p (Optional[float], optional) – Value for the dL_p2p parameter. Default is None.

  • L_tilt (int, optional) – Length parameter in microns. Default is 10.

  • xs_ring (str, optional) – Layer or cross-section name used by the device. Default is ‘strip’.

  • sharp_patch (bool, optional) – Whether to add geometry patches for sharp corners or cladding continuity. Default is True.

  • Euler_trasition (bool, optional) – Value for the Euler_trasition parameter. Default is False.

  • show_pins (bool, optional) – Whether to draw pin markers in the generated layout. Default is False.

  • xs_heater (str, optional) – Layer or cross-section name used by the device. Default is ‘heater’.

  • w_heater (float, optional) – Width parameter in microns. Default is 0.

  • xs_metal (str, optional) – Layer or cross-section name used by the device. Default is ‘metal’.

  • w_metal (float, optional) – Width parameter in microns. Default is 8.

  • via_h2m (Any, optional) – Via definition used between heater and metal layers. Default is None.

  • isl (Any, optional) – Isolation-trench definition used by the electrical layout. Default is None.

  • A_ht (float, optional) – Angle parameter in degrees. Default is 270.

  • ht_notch_dual (bool, optional) – Value for the ht_notch_dual parameter. Default is True.

  • epin_ht_dX (int, optional) – Value for the epin_ht_dX parameter. Default is 10.

  • epin_ht_dY (int, optional) – Value for the epin_ht_dY parameter. Default is 3.

  • xs_metal_imp (str, optional) – Layer or cross-section name used by the device. Default is ‘metal’.

  • via_i2m (Any, optional) – Via definition used between implant and metal layers. Default is None.

  • xs_p (str, optional) – Layer or cross-section name used by the device. Default is ‘p’.

  • xs_n (str, optional) – Layer or cross-section name used by the device. Default is ‘n’.

  • xs_cont_wg (Optional[str], optional) – Layer or cross-section name used by the device. Default is None.

  • w_p (float, optional) – Width parameter in microns. Default is 3.

  • gap_p_i (float, optional) – Spacing or gap parameter in microns. Default is 1.

  • gap_n_i (float, optional) – Spacing or gap parameter in microns. Default is 1.

  • w_n (float, optional) – Width parameter in microns. Default is 3.

  • offset_i (float, optional) – Value for the offset_i parameter. Default is 0.

  • A_imp_in (int, optional) – Angle parameter in degrees. Default is 180.

  • A_imp_out (int, optional) – Angle parameter in degrees. Default is 180.

  • xs_pcont (str, optional) – Layer or cross-section name used by the device. Default is ‘pp’.

  • xs_ncont (str, optional) – Layer or cross-section name used by the device. Default is ‘np’.

  • w_pcont (float, optional) – Width parameter in microns. Default is 3.

  • w_ncont (float, optional) – Width parameter in microns. Default is 3.

  • sp_cont (float, optional) – Spacing or gap parameter in microns. Default is 0.2.

  • w_ovlp (float, optional) – Width parameter in microns. Default is 0.2.

  • bus_dopping (bool, optional) – Value for the bus_dopping parameter. Default is True.

  • p_in_n_out (bool, optional) – Value for the p_in_n_out parameter. Default is False.

PIN_MRR_MM_Allpass#

../../../../_images/PIN_MRR_MM_Allpass.png
class mxpic.components.primitives.active.rings.PIN_MRR_MM_Allpass(name=None, r_ring=10, w_ring=0.55, gap=0.2, w_bus=0.45, R_cp=None, A_cp=0, R_att=10, R_att_min=10, A_att=10, offset_X=0, offset_Y=0, w_wg=0.45, Ltp_bus=10, dL_p2p=None, xs_ring='strip', sharp_patch=True, show_pins=False, xs_heater='heater', w_heater=0, xs_metal='metal', w_metal=8, via_h2m=None, isl=None, A_ht=270, ht_notch_dual=True, epin_ht_dX=10, epin_ht_dY=3, xs_metal_imp='metal', via_i2m=None, xs_p='p', xs_n='n', xs_cont_wg=None, w_p=3, w_n=3, w_i=1, offset_i=0, A_imp_in=180, A_imp_out=180, sp_cont=0.2, w_ovlp=0.2, bus_dopping=True, cell_xs_transition=None, p_in_n_out=False)#

Bases: AED_Ring_PIN

PIN MRR MM Allpass primitive component.

This component builds the PIN MRR MM Allpass layout cell.

Parameters:

  • name (Optional[str], optional) – Unique identifier for the device cell. Default is None.

  • r_ring (float, optional) – Radius parameter in microns. Default is 10.

  • w_ring (float, optional) – Width parameter in microns. Default is 0.55.

  • gap (float, optional) – Spacing or gap parameter in microns. Default is 0.2.

  • w_bus (float, optional) – Width parameter in microns. Default is 0.45.

  • R_cp (Any, optional) – Radius parameter in microns. Default is None.

  • A_cp (int, optional) – Angle parameter in degrees. Default is 0.

  • R_att (int, optional) – Radius parameter in microns. Default is 10.

  • R_att_min (int, optional) – Radius parameter in microns. Default is 10.

  • A_att (int, optional) – Angle parameter in degrees. Default is 10.

  • offset_X (float, optional) – Value for the offset_X parameter. Default is 0.

  • offset_Y (float, optional) – Value for the offset_Y parameter. Default is 0.

  • w_wg (float, optional) – Width parameter in microns. Default is 0.45.

  • Ltp_bus (int, optional) – Length parameter in microns. Default is 10.

  • dL_p2p (Optional[float], optional) – Value for the dL_p2p parameter. Default is None.

  • xs_ring (str, optional) – Layer or cross-section name used by the device. Default is ‘strip’.

  • sharp_patch (bool, optional) – Whether to add geometry patches for sharp corners or cladding continuity. Default is True.

  • show_pins (bool, optional) – Whether to draw pin markers in the generated layout. Default is False.

  • xs_heater (str, optional) – Layer or cross-section name used by the device. Default is ‘heater’.

  • w_heater (float, optional) – Width parameter in microns. Default is 0.

  • xs_metal (str, optional) – Layer or cross-section name used by the device. Default is ‘metal’.

  • w_metal (float, optional) – Width parameter in microns. Default is 8.

  • via_h2m (Any, optional) – Via definition used between heater and metal layers. Default is None.

  • isl (Any, optional) – Isolation-trench definition used by the electrical layout. Default is None.

  • A_ht (float, optional) – Angle parameter in degrees. Default is 270.

  • ht_notch_dual (bool, optional) – Value for the ht_notch_dual parameter. Default is True.

  • epin_ht_dX (int, optional) – Value for the epin_ht_dX parameter. Default is 10.

  • epin_ht_dY (int, optional) – Value for the epin_ht_dY parameter. Default is 3.

  • xs_metal_imp (str, optional) – Layer or cross-section name used by the device. Default is ‘metal’.

  • via_i2m (Any, optional) – Via definition used between implant and metal layers. Default is None.

  • xs_p (str, optional) – Layer or cross-section name used by the device. Default is ‘p’.

  • xs_n (str, optional) – Layer or cross-section name used by the device. Default is ‘n’.

  • xs_cont_wg (Optional[str], optional) – Layer or cross-section name used by the device. Default is None.

  • w_p (float, optional) – Width parameter in microns. Default is 3.

  • w_n (float, optional) – Width parameter in microns. Default is 3.

  • w_i (float, optional) – Width parameter in microns. Default is 1.

  • offset_i (float, optional) – Value for the offset_i parameter. Default is 0.

  • A_imp_in (int, optional) – Angle parameter in degrees. Default is 180.

  • A_imp_out (int, optional) – Angle parameter in degrees. Default is 180.

  • sp_cont (float, optional) – Spacing or gap parameter in microns. Default is 0.2.

  • w_ovlp (float, optional) – Width parameter in microns. Default is 0.2.

  • bus_dopping (bool, optional) – Value for the bus_dopping parameter. Default is True.

  • cell_xs_transition (Any, optional) – Cell or component dependency used by this device. Default is None.

  • p_in_n_out (bool, optional) – Value for the p_in_n_out parameter. Default is False.

PIN_MRR_MM_Adddrop#

../../../../_images/PIN_MRR_MM_Adddrop.png
class mxpic.components.primitives.active.rings.PIN_MRR_MM_Adddrop(name=None, r_ring=10, w_ring=0.55, gap=0.2, w_bus=0.45, R_cp=None, A_cp=0, R_att=10, R_att_min=10, A_att=10, offset_X=0, offset_Y=0, w_wg=0.45, Ltp_bus=10, dL_p2p=None, xs_ring='strip', sharp_patch=True, show_pins=False, xs_heater='heater', w_heater=0, xs_metal='metal', w_metal=8, via_h2m=None, isl=None, A_ht=270, ht_notch_dual=True, epin_ht_dX=10, epin_ht_dY=3, xs_metal_imp='metal', via_i2m=None, xs_p='p', xs_n='n', xs_cont_wg=None, w_p=3, w_n=3, w_i=1, offset_i=0, A_imp_in=180, A_imp_out=180, sp_cont=0.2, w_ovlp=0.2, bus_dopping=True, cell_xs_transition=None, p_in_n_out=False)#

Bases: AED_Ring_PIN

PIN MRR MM Adddrop primitive component.

This component builds the PIN MRR MM Adddrop layout cell.

Parameters:

  • name (Optional[str], optional) – Unique identifier for the device cell. Default is None.

  • r_ring (float, optional) – Radius parameter in microns. Default is 10.

  • w_ring (float, optional) – Width parameter in microns. Default is 0.55.

  • gap (float, optional) – Spacing or gap parameter in microns. Default is 0.2.

  • w_bus (float, optional) – Width parameter in microns. Default is 0.45.

  • R_cp (Any, optional) – Radius parameter in microns. Default is None.

  • A_cp (int, optional) – Angle parameter in degrees. Default is 0.

  • R_att (int, optional) – Radius parameter in microns. Default is 10.

  • R_att_min (int, optional) – Radius parameter in microns. Default is 10.

  • A_att (int, optional) – Angle parameter in degrees. Default is 10.

  • offset_X (float, optional) – Value for the offset_X parameter. Default is 0.

  • offset_Y (float, optional) – Value for the offset_Y parameter. Default is 0.

  • w_wg (float, optional) – Width parameter in microns. Default is 0.45.

  • Ltp_bus (int, optional) – Length parameter in microns. Default is 10.

  • dL_p2p (Optional[float], optional) – Value for the dL_p2p parameter. Default is None.

  • xs_ring (str, optional) – Layer or cross-section name used by the device. Default is ‘strip’.

  • sharp_patch (bool, optional) – Whether to add geometry patches for sharp corners or cladding continuity. Default is True.

  • show_pins (bool, optional) – Whether to draw pin markers in the generated layout. Default is False.

  • xs_heater (str, optional) – Layer or cross-section name used by the device. Default is ‘heater’.

  • w_heater (float, optional) – Width parameter in microns. Default is 0.

  • xs_metal (str, optional) – Layer or cross-section name used by the device. Default is ‘metal’.

  • w_metal (float, optional) – Width parameter in microns. Default is 8.

  • via_h2m (Any, optional) – Via definition used between heater and metal layers. Default is None.

  • isl (Any, optional) – Isolation-trench definition used by the electrical layout. Default is None.

  • A_ht (float, optional) – Angle parameter in degrees. Default is 270.

  • ht_notch_dual (bool, optional) – Value for the ht_notch_dual parameter. Default is True.

  • epin_ht_dX (int, optional) – Value for the epin_ht_dX parameter. Default is 10.

  • epin_ht_dY (int, optional) – Value for the epin_ht_dY parameter. Default is 3.

  • xs_metal_imp (str, optional) – Layer or cross-section name used by the device. Default is ‘metal’.

  • via_i2m (Any, optional) – Via definition used between implant and metal layers. Default is None.

  • xs_p (str, optional) – Layer or cross-section name used by the device. Default is ‘p’.

  • xs_n (str, optional) – Layer or cross-section name used by the device. Default is ‘n’.

  • xs_cont_wg (Optional[str], optional) – Layer or cross-section name used by the device. Default is None.

  • w_p (float, optional) – Width parameter in microns. Default is 3.

  • w_n (float, optional) – Width parameter in microns. Default is 3.

  • w_i (float, optional) – Width parameter in microns. Default is 1.

  • offset_i (float, optional) – Value for the offset_i parameter. Default is 0.

  • A_imp_in (int, optional) – Angle parameter in degrees. Default is 180.

  • A_imp_out (int, optional) – Angle parameter in degrees. Default is 180.

  • sp_cont (float, optional) – Spacing or gap parameter in microns. Default is 0.2.

  • w_ovlp (float, optional) – Width parameter in microns. Default is 0.2.

  • bus_dopping (bool, optional) – Value for the bus_dopping parameter. Default is True.

  • cell_xs_transition (Any, optional) – Cell or component dependency used by this device. Default is None.

  • p_in_n_out (bool, optional) – Value for the p_in_n_out parameter. Default is False.

PIN_MRR_STD_Allpass#

../../../../_images/PIN_MRR_STD_Allpass.png
class mxpic.components.primitives.active.rings.PIN_MRR_STD_Allpass(name=None, r_ring=10, w_ring=0.55, gap=0.2, w_bus=0.45, A_cp=0, w_wg=0.45, Ltp_bus=10, dL_p2p=None, L_tilt=10, xs_ring='strip', sharp_patch=True, show_pins=False, xs_heater='heater', w_heater=0, xs_metal='metal', w_metal=8, via_h2m=None, isl=None, A_ht=270, ht_notch_dual=True, epin_ht_dX=10, epin_ht_dY=3, xs_metal_imp='metal', via_i2m=None, xs_p='p', xs_n='n', xs_cont_wg=None, w_p=3, w_n=3, w_i=1, offset_i=0, A_imp_in=180, A_imp_out=180, sp_cont=0.2, w_ovlp=0.2, bus_dopping=True, cell_xs_transition=None, p_in_n_out=False)#

Bases: AED_Ring_PIN

PIN MRR STD Allpass primitive component.

This component builds the PIN MRR STD Allpass layout cell.

Parameters:

  • name (Optional[str], optional) – Unique identifier for the device cell. Default is None.

  • r_ring (float, optional) – Radius parameter in microns. Default is 10.

  • w_ring (float, optional) – Width parameter in microns. Default is 0.55.

  • gap (float, optional) – Spacing or gap parameter in microns. Default is 0.2.

  • w_bus (float, optional) – Width parameter in microns. Default is 0.45.

  • A_cp (int, optional) – Angle parameter in degrees. Default is 0.

  • w_wg (float, optional) – Width parameter in microns. Default is 0.45.

  • Ltp_bus (int, optional) – Length parameter in microns. Default is 10.

  • dL_p2p (Optional[float], optional) – Value for the dL_p2p parameter. Default is None.

  • L_tilt (int, optional) – Length parameter in microns. Default is 10.

  • xs_ring (str, optional) – Layer or cross-section name used by the device. Default is ‘strip’.

  • sharp_patch (bool, optional) – Whether to add geometry patches for sharp corners or cladding continuity. Default is True.

  • show_pins (bool, optional) – Whether to draw pin markers in the generated layout. Default is False.

  • xs_heater (str, optional) – Layer or cross-section name used by the device. Default is ‘heater’.

  • w_heater (float, optional) – Width parameter in microns. Default is 0.

  • xs_metal (str, optional) – Layer or cross-section name used by the device. Default is ‘metal’.

  • w_metal (float, optional) – Width parameter in microns. Default is 8.

  • via_h2m (Any, optional) – Via definition used between heater and metal layers. Default is None.

  • isl (Any, optional) – Isolation-trench definition used by the electrical layout. Default is None.

  • A_ht (float, optional) – Angle parameter in degrees. Default is 270.

  • ht_notch_dual (bool, optional) – Value for the ht_notch_dual parameter. Default is True.

  • epin_ht_dX (int, optional) – Value for the epin_ht_dX parameter. Default is 10.

  • epin_ht_dY (int, optional) – Value for the epin_ht_dY parameter. Default is 3.

  • xs_metal_imp (str, optional) – Layer or cross-section name used by the device. Default is ‘metal’.

  • via_i2m (Any, optional) – Via definition used between implant and metal layers. Default is None.

  • xs_p (str, optional) – Layer or cross-section name used by the device. Default is ‘p’.

  • xs_n (str, optional) – Layer or cross-section name used by the device. Default is ‘n’.

  • xs_cont_wg (Optional[str], optional) – Layer or cross-section name used by the device. Default is None.

  • w_p (float, optional) – Width parameter in microns. Default is 3.

  • w_n (float, optional) – Width parameter in microns. Default is 3.

  • w_i (float, optional) – Width parameter in microns. Default is 1.

  • offset_i (float, optional) – Value for the offset_i parameter. Default is 0.

  • A_imp_in (int, optional) – Angle parameter in degrees. Default is 180.

  • A_imp_out (int, optional) – Angle parameter in degrees. Default is 180.

  • sp_cont (float, optional) – Spacing or gap parameter in microns. Default is 0.2.

  • w_ovlp (float, optional) – Width parameter in microns. Default is 0.2.

  • bus_dopping (bool, optional) – Value for the bus_dopping parameter. Default is True.

  • cell_xs_transition (Any, optional) – Cell or component dependency used by this device. Default is None.

  • p_in_n_out (bool, optional) – Value for the p_in_n_out parameter. Default is False.